Problem jest następujący:
Ostatnio router (AR41/2, na chipie conexanta) czasami po prostu pada. Nie da się dostać do strony konfiguracyjnej (jest pusta), nie działa także serwer DNS. Co dziwne, wszystko pozostałe (routing, virutal servery, dhcp) działa poprawnie, czyli jest dostęp do internetu. Inną dziwną rzeczą jest dla mnie to, że po odłączeniu jakiejś stacji od sieci, router znowu zaczyna działać. Po ponownym podłączeniu czasem jest ok przez jakiś czas, a czasem znowu pada.
Sieć składa się z routero-switcha, routera i 4 pecetów.
Pytanie: spotkał się ktoś z takim problemem?

Log:

12/22/2006 1:31:51> getSwVersion: no revision.txt file 
12/22/2006 1:30:49> Received time from Time Server 131.107.1.10
1/1/1970 0:3:55> Regained contact with DNS servers
1/1/1970 0:3:49> PPP1 Session is up.
1/1/1970 0:3:48> No Static Session Information is defined.
1/1/1970 0:3:48> Initialized Dynamic NAPT.
1/1/1970 0:3:48> NAT/NAPT Session Start: interface ppp1, WAN IP is xx.xx.xx.xx
1/1/1970 0:3:48> PPP1: DNS Secondary IP address is 217.98.63.164
1/1/1970 0:3:48> PPP1: DNS Primary IP address is 194.204.152.34
1/1/1970 0:3:48> PPP1: PPP Gateway IP address is xx.xx.xx.xx
1/1/1970 0:3:48> PPP1: PPP IP address is xx.xx.xx.xx
1/1/1970 0:3:48> PPP CHAP Authentication success
1/1/1970 0:3:48> PPP1 PPPoE Session is established.
1/1/1970 0:2:50> Lost contact with DNS servers
1/1/1970 0:2:47> PPP1 PPPoE Session is terminated.
1/1/1970 0:2:47> PPP1 Session is down.
1/1/1970 0:2:47> PPP1 PPPoE Session is established.
1/1/1970 0:1:46> PPP1 PPPoE Session is terminated.
1/1/1970 0:1:46> PPP1 Session is down.
1/1/1970 0:1:46> PPP1 PPPoE Session is established.
1/1/1970 0:0:45> PPP1 PPPoE Session is terminated.
1/1/1970 0:0:45> PPP1 Session is down.
1/1/1970 0:0:45> PPP1 PPPoE Session is established.
1/1/1970 0:0:24> ADSL connected
1/1/1970 0:0:24> ATM layer is up, cell delineation achieved 
1/1/1970 0:0:24> ATM Connected 
1/1/1970 0:0:18> ClientEntryAdd: Delete old Entry to make room!!!
1/1/1970 0:0:17> ClientEntryAdd: Delete old Entry to make room!!!
1/1/1970 0:0:17> ClientEntryAdd: Delete old Entry to make room!!!
1/1/1970 0:0:17> ClientEntryAdd: Delete old Entry to make room!!!
1/1/1970 0:0:17> ClientEntryAdd: Delete old Entry to make room!!!
1/1/1970 0:0:0> Washer - washer_reg called! 
1/1/1970 0:0:0> CfgMgr: 'Washer.dlz' module loaded.
1/1/1970 0:0:0> CfgMgr: 'Shtm.dlz' module loaded.
1/1/1970 0:0:0> Dynamic NAPT is enabled
1/1/1970 0:0:0> ATM: Setting up vcc0, VPI=0, VCI=35 
1/1/1970 0:0:0> ATM: Detected 
1/1/1970 0:0:0> Ethernet Device 0 Detected

Widać tu coś niepokojącego, ale wiele mi to nie mówi ;].