D-link pod Linuksa (Fedora Core 5)

0

Mam D-link DWL 520+ i mam problem z zainstalowaniem jej na Linuksie (Fedora Core 5). Otóż sterowniki wgrałem za pomocą programu acx100, wykrywa kartę, lecz po wpisaniu komendy iwconfig pojawia mi się coś takiego:

[root@localhost ~]# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

Warning: Driver for device wlan0 has been compiled with version 20
of Wireless Extension, while this program supports up to version 19.
Some things may be broken...

wlan0 IEEE 802.11b+ ESSID:"STA03A899" Nickname:"acx v0.3.35"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:22 Mb/s Tx-Power=18 dBm Sensitivity=176/255
Retry min limit:7 RTS thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

sit0 no wireless extensions.

[root@localhost ~]#

Wszystko działa (Link Quality, Signal level po wpisaniu kucza, ip, bramy oraz ip podsiecidziałają (noise level także ale nie zawsze i ok 3/100). Ale nie wykrywa mi access point'a. Nie wiem co zorbić. Może mi ktoś pomoże? Męcze się z tym już ponad tydzień....

0

a co pokazuje
iwlist wlan0 scan
oraz
iwconfig -v
?

0

[root@localhost ~]# iwlist wlan0 scan
Warning: Driver for device wlan0 has been compiled with version 20
of Wireless Extension, while this program supports up to version 19.
Some things may be broken...

wlan0     Interface doesn't support scanning : Resource temporarily unavailable

[root@localhost ~]# iwconfig -v
iwconfig  Wireless-Tools version 28
          Compatible with Wireless Extension v11 to v19.

Kernel    Currently compiled with Wireless Extension v20.

wlan0     Recommend Wireless Extension v9 or later,
          Currently compiled with Wireless Extension v20.

[root@localhost ~]#


0

No.. mam dokladnie to samo, z tym ze moja karta to WL-3805, googlalem ostatnio o tym i wyczytałem ze jest to spowodowane złą wersję wireless-tools, nie wiem ja sobie dałem spokoj bo i tak mi nie potrzebna ta sieciowka, a Ty pokombinuj z tym wireless-tools

0

;-( W tym problem

Już z tym kombinowałem......

0
http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html napisał(a)
  1. In the rare cases where your kernel isn't compiled with Wireless Extensions (/proc/net/wireless non-existent), you need to recompile it with Wireless Extensions (CONFIG_NET_RADIO enabled).
  2. After recompiling a kernel with Wireless Extension, you have to recompile your driver or the Pcmcia package as well (and restart it).
  3. All versions of Wireless Tools up to version 26 need to be compiled for the precise version of Wireless Extension present on the system. Starting with Wireless Tools 27, Wireless Tools can handle multiple versions of Wireless Extension without recompile.
  4. The Wireless Extensions and Wireless Tools version numbers will not match with each other. The Wireless Tools and the Wireless Extensions (the underlying API) evolve independantly of each other. The command iwconfig --version gives you the detail of your setup.
  5. Compilation of the Wireless Tools used to be tricky, especially in the header area. I believe this has been fixed for good.
  6. For kernels before 2.2.14/2.3.30, use Wireless Tools version 19.
  7. For kernel after 2.2.14/2.3.30 use Wireless Tools version 20 or greater.
  8. For kernel after 2.6.13 use Wireless Tools version 27 or greater.
  9. The tools and the wireless library are GPL.
  10. In the old time, you could upgrade Wireless Extensions by just changing wireless.h. Starting with Wireless Extensions v12, this is no longer true, you need to apply the full patch to the kernel. See below for the patches.

got it? musisz zainstaować inne wireless-tools... a to że się da pisze tu: http://gentoo-portage.com/net-wireless/wireless-tools

0

Próbowałem, ale nic z tego :/ (wgrywałem róźne mimo, że tam pisze, że dla mojego jądra jest większe od 27 (czyli w sumie 27 i 28)... wczesniejsze nie zabardzo też się kompilują powstaje jakiś błąd)

Lecz jedyne co się zmienia to :

Warning: Driver for device wlan0 has been compiled with version 20
of Wireless Extension, while this program supports up to version 19.
Some things may be broken...

W zależności od wresji Wireless-tools to ta liczba 19 zmienia się (gdy wersja 24 na 14, 27 na 17 itp), to więc wnioskuje że potrzeba wersję większą od tej którą aktualnie mam a w tym problem, ze taka nie istnieje :/

0

hmm... dziwne, na gentoo działa ładnie...

0

W wielu tych kursach internetowych pisze, że trzeba sterowniki z winXP przegrać do folderu /firmware i tak też zrobiłem, ale zastanawiam się, bo to jest nowsza wersja, to może gdzieś indziej trzeba je zgrać, albo w ogóle?

0

A może za pomocą Ndiswrappera?
Tylko, że jak daje iwconfig (po tym jak zainstalowałęm go pokazuje mi że zainstalował sterownik) wypisuje mi coś takiego:

[root@localhost ~]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

sit0      no wireless extensions.

[root@localhost ~]#

Nie ma tam żadnego wlan0 :/

0

a dales
ifconfig wlan0 up ?

0

to mi wyskoczyło"


wlan0 ; unkown interface; no such device

0

a czy

root@slack:/home/strzelba# ndiswrapper -l
Installed drivers:
tiacxln         driver installed, hardware present

pokazuje cos podobnego?

Jesli nie to znaczy ze zle zainstalowałes sterownik do karty.
I zakładam ze dales po instalacji

# depmod -a
# modprobe ndiswrapper 

btw pokaz jeszcze co daje lspci

0

Tak miałem już wfgrany sterownik, pokazało mi się coś podobnego do Twojego (tylko nazwa sterownika inna ;)) )

linux-mxz0:~ # lspci
00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2)
00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2)
00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2)
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)
00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
02:09.0 Network controller: Texas Instruments ACX 100 22Mbps Wireless Interface
linux-mxz0:~ #         
0

spróbuj jeszcze
echo 'alias wlan0 ndiswrapper' >> /etc/modprobe.conf

A w ogole to zrob jak tu i bedzie dzialac
http://ndiswrapper.sourceforge.net/mediawiki/index.php/Main_Page

problemy są natomiast z roznymi wersjami ndisa, ja mam taką i mi karta dziala w systemie.

root@slack:/home/strzelba# ndiswrapper -v
utils version: 1.8
driver version:        1.14
vermagic:       2.6.15.1 SMP preempt PENTIUM4 gcc-3.4
0
LukaStrz napisał(a)

problemy są natomiast z roznymi wersjami ndisa, ja mam taką i mi karta dziala w systemie.

otoz to, mi z moim dlinkiem najnowsze dostepne (1.4 wtedy chyba) nie chcial dzialac,a 1.2 smiga bez problemow...

0

Przperaszam, że tak nie odpisywałem, ale miał przyjść specjalista i przyszedł i okazało się że ja lepiej umiem od niego, ale i tak nic nie zrobiłem :/, no i straciłęm całkowitą nadzieję, lecz dzisiaj się wziąłem i oto do czego doszedłem :

# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

sit0      no wireless extensions.

wlan0     IEEE 802.11b  ESSID:off/any
          Mode:Managed  Frequency:2.427 GHz  Access Point: Not-Associated
          Bit Rate:11 Mb/s   Tx-Power:0 dBm   Sensitivity=0/3
          RTS thr:4096 B   Fragment thr:4095 B
          Encryption key:***********   Security mode:restricted
          Power Management:off
          Link Quality:100/100  Signal level:-64 dBm  Noise level:-256 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

iwlist wlan0 scan
wlan0     Scan completed :
          Cell 01 - Address: 00:0E:8E:7C:0F:38
                    ESSID:""
                    Protocol:IEEE 802.11FH
                    Mode:Managed
                    Frequency:2.427 GHz (Channel 4)
                    Quality:0/100  Signal level:72/154  Noise level:0/154
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              12 Mb/s; 24 Mb/s; 36 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0

Niestety, nie wiem co dalej, jak wpisuje "iwconfig wlan0 ap 008E0F:38" to po wpisaniu "iwconfig" pokazuje mi się no-access-point..., może wiecie jak to rozwiącać?

AHA
i dziękuję wam, bo mi pomogliście ;)), trzeba było tylko zmienić wersję ndiswrappera ;)

0

Kawałek mojego starego skryptu do startowania sieciowki:

echo "Odpalamy konfiguracje sieciowki wlan0 :>"
modprobe ndiswrapper
sleep 2
iwconfig wlan0 mode managed
iwconfig wlan0 key **********
iwconfig wlan0 essid sp-16
sleep 2
iwconfig wlan0 essid sp-16
ifconfig wlan0 10.0.0.17 netmask 255.255.255.0
route add default gw 10.0.0.254
iwconfig wlan0 essid sp-16 key open **********
dhcpcd wlan0

Zobacz czy nie zapominasz o czyms.
A "dhcpcd wlan0" to juz zalezy do Twojej sieci

0

ie zapomniałem o niczym, ale:

iwconfig wlan0 essid nazwa_sieci

Wpisuje właśnie to polecenie, no i gdy wpisze "iwconfig" pojawia mi się dalej

ESSID:off/any

I nie wiem co zrobić :/....

1 użytkowników online, w tym zalogowanych: 0, gości: 1